STEPPING MO T O RS 5 Phase with A 5-Phase with DC Driver Stepping Controller 2 Phase with DC Driver SG8030JY ························································B-244 Stepping Accessories ORIENTAL MOTOR GENERAL CATALOGUE STEPPING Compact and Simple Controllers MO SG8030JY T O RS The SG8030JY is a compact controller that switches between two control methods according to the application: sequential positioning and data selection positioning. With sequential positioning mode, you execute up to four positioning control operations in the pre-determined sequence by just inputting the 5-Phase with A start command from the programmable controller. In data selection positioning mode, positioning is controlled by selecting one of four sets of pre-registered positioning data and
Now the Panel-Mount Model isavailable.Allow conventional delay for
inputting the start command from the
shipping. See your agency for detail. programmable controller. SG8030JY-D SG8030JY-U 5-Phase with DC Driver
Ⅵ Main Specifications High-Performance Packed in
Set data with touch keys on front panel (record in
48mmϫ48mm Compact Units
Ⅲ With dimensions of 48mmϫ48mmϫ83.8mm, these
units are the smallest of Oriental Motors controllers.
They come in Flush Mounting and Recessed Mounting
Starting pulse speed 100-10000 HzAcceleration rate 1-100 ms/kHz
For the acceleration/deceleration pattern, you may select the linear or Stepping S-shaped pattern.
Ⅲ In addition to the linear acceleration/deceleration
acceleration/deceleration along an S-shaped pattern.
Sensor detection of home throgh designation of
2-Phase with DC Driver
When you select this S-shaped pattern, the motor can
mechanical home detection direction of rotation.
DC 24 V photocoupler input, input resistance 4.7 k Ω
current sinking inputPNP transistor output linked to photocoupler, 24V
The control methods can be switched.
DC, 25mA or less, current sourcing output
Ⅲ You can also switch the control between sequential
positioning and data selection positioning. Stepping Functions
Ⅲ These stepping motor controllers, they have all the most
commonly used functions. ⅷControl modes: External, Program, Test
ⅷOperating modes: Positioning, Return to mechanical
Example of Basic System Configuration Accessories SG8030JY ORIENTAL MOTOR GENERAL CATALOGUE STEPPING
Ⅵ Operating methods MO Sequential Positioning Type Data Selection Positioning Type T O RS ositioning P
Sequential positioning type performs positioning in order from the
Data selection positioning type performs positioning in order after
first data every time a START signal is input.
positioning data 1-4 are selected and a START signal is input. 5 Phase with A External input mode
When a START signal is input, it moves towards the preset sensor at the operating pulse speed (VR), to return to the origin. Return to mec 5-Phase with DC Driver
It continuously operates as long as a CW or CCW scan signal is
When operating at the continuous operation mode, it keeps the
input, no matter what operating mode is set (It reduces the speed
operation as long as a CW or CCW scan signal is input (It reduces
and stops when a OFF signal is input).
the speed and stops when a OFF signal is input). operation
The next four operation can be confirmed manually by using the
Data selection positioning operationContinuous operation
Confirmation of Stepping operation man
Ⅵ Wiring diagram
Ⅵ Signal table 2 Phase with DC Driver
Signal names and functions of Sequential positioning type andData selection positioning type differ in Pin No. 1, 10, 11 only.
q When in the Sequential positioning type
w When in the Data selection positioning type
Stepping SG8030JY
q : Switching positioning and home detection
w : Switching positioning and home detection
Input Start signal for Positioning and Home detection operation
Accessories
7 Pulse <CW pulse> Output Pulse <CW-pulse output terminal>
Output Direction <CCW-pulse output terminal>
✽1 The pulse output section uses a constant-current circuit, so no external
Input Stop all operation Stop busy output
If another power supply is used for the pulse output section, for example +5V
power, connect the 24V DC and another power supply GND terminals each other.
✽3 This should be conductive (B contact) during normal operation.
When not using the emergency stop input signal, always connect to the
The "E.StoP" message is displayed when the power supply goes off.
✽4 The names in angle brackets < > signals are for data selection
The operating modes given in square brackets [ ] are activated when operationmode select input is on. The names in angle brackets < > signals are for 2-pulse output. ORIENTAL MOTOR GENERAL CATALOGUE STEPPING MO T O RS
Ⅵ Dimensions Scale 1/4, Unit=mm Mass: 0.1kg (Without accessories) 5-Phase with A
ⅷSG8030JY-D
ⅷSG8030JY-U 5-Phase with DC Driver Stepping 2-Phase with DC Driver Stepping Accessories ORIENTAL MOTOR GENERAL CATALOGUE
Evidence Based Management of Severe Acute Asthma in Young Children Suzanne Schuh, MD, FRCP(C), FAAP, ABPEM Research Director, Division of Paediatric Emergency Department The Hospital for Sick Children, Toronto, Canada Professor of Pediatrics, University of Toronto, Toronto, Canada A definitive diagnosis of asthma is difficult to make in young children. While there are children with recu
11535 Sorrento Valley Blvd, San Diego, CA www.mpexpharma.com Aeroquin (proprietary aerosol formulation of levofloxacin) a reduced risk clinical program; 100% of rights retained• Compelling results from Phase 2b trial in Cystic Fibrosis• Preparing to initiate Phase 3 trial in Cystic Fibrosis Separate broad technology platform focused on efflux pump inhibitors (EPIs) • Coll
STEPPING
STEPPING